聯 系 人：段煜
電 話：15214379366
手 機：16602115336
地 址：上海市崇明縣長興鎮潘園公路1800號2號樓9703室（上海泰和經濟發展區）
郵 編：201913
傳 真：021-80186165
郵 箱：435399850@qq.com
阿儀網商鋪：http://www.app17.com/c110001/
手機網站：m.jwswbio.com
價格：電議 型號：
原產地：中國大陸發布時間：2022/4/6 14:01:35
采購度：156
本公司4月6日14時02分報道：（http://www.app17.com/c110001/products/d11328987.html）
3. 預處理后的樣本無需稀釋，直接取 10μL 加樣即可。
4. 嚴格按照說明書中標明的時間、加液量及順序進行溫育操作。
5. 所有液體組分使用前充分搖勻。
試劑盒組成
洗板方法
1. 手工洗板：甩盡孔內液體，每孔加滿洗滌液，靜置 1min 后甩盡孔內液體，在吸水紙上拍干，如此洗板 5 次。
2. 自動洗板機：每孔注入洗液 350μL，浸泡 1min，洗板 5 次。
| 名稱 | 96 孔配置 | 48 孔配置 | 備注 |
| 微孔酶標板 | 12 孔×8 條 | 12 孔×4 條 | 無 |
| 標準品 | 0.3mL | 0.3mL | 無 |
| 樣本稀釋液 | 6mL | 3mL | 無 |
| 檢測抗體-HRP | 10mL | 5mL | 無 |
| 20×洗滌緩沖液 | 25mL | 15mL | 按說明書進行稀釋 |
| 底物 A | 6mL | 3mL | 無 |
| 底物 B | 6mL | 3mL | 無 |
| 終止液 | 6mL | 3mL | 無 |
| 封板膜 | 2 張 | 2 張 | 無 |
| 說明書 | 1 份 | 1 份 | 無 |
| 自封袋 | 1 個 | 1 個 | 無 |
操作步驟
1. 從室溫平衡 20min 后的鋁箔袋中取出所需板條，剩余板條用自封袋密封放回 4℃。
2. 設置標準品孔和樣本孔，標準品孔各加不同濃度的標準品 50μL；
3. 待測樣本孔先加待測樣本 10μL，再加樣本稀釋液 40μL；
4. 隨后標準品孔和樣本孔中每孔加入辣根過氧化物酶（HRP）標記
注：標準品濃度依次為：40、20、10、5、2.5、0 ng/mL.
的檢測抗體 100μL，用封板膜封住反應孔，37℃水浴鍋或恒溫箱溫
試劑的準備
育 60min。
20×洗滌緩沖液的稀釋：蒸餾水按 1：20 稀釋，即 1 份的 20×洗滌
5. 棄去液體，吸水紙上拍干，每孔加滿洗滌液，靜置 1min，甩去
緩沖液加 19 份的蒸餾水。
洗滌液，吸水紙上拍干，如此重復洗板 5 次（也可用洗板機洗板）。
6. 每孔加入底物 A、B 各 50μL，37℃避光孵育 15min。
7. 每孔加入終止液 50μL，15min 內，在 450nm 波長處測定各孔的OD 值。
結果判斷
繪制標準曲線：在 Excel 工作表中，以標準品濃度作橫坐標，對應OD 值作縱坐標，繪制出標準品線性回歸曲線，按曲線方程計算各樣本濃度值。
試劑盒性能
1. 準確性：標準品線性回歸與預期濃度相關系數 R 值，大于等于0.9900。
2. 靈敏度：檢測濃度小于 0.1 ng/mL。
3. 特異性：不與其它可溶性結構類似物交叉反應。
4. 重復性：板內變異系數小于 10%、板間變異系數小于 15%。
5. 貯藏：2-8℃，避光防潮保存。
6. 有效期：6 個月免責聲明
1. 試劑盒僅供研究使用，不得用于臨床實驗或人體實驗，否則所產生的一切后果，由實驗者承擔，本公司概不負責。
2. 嚴格按照說明書操作，實驗者違反說明書操作，后果由實驗者承擔。
FOR RESEARCH USE ONLY.
NOT FOR USE IN DIAGNOSTIC PROCEDURES.
Human Collagenase I (Collagenase I) ELISA Kit
instruction
Intended use
This Collagenase I ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures. The Stop Solution changes the color from blue to yellow ａnd the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of Collagenase I in the sample, this Collagenase I ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus Collagenase I concentration. The concentration of Collagenase I in the samples is then determined by comparing the O.D. of the samples to the standard curve.
Sample collection and storages
Serum - Use a serum separator tube and allow samples to clot for 30 minutes
before centrifugation for 10 minutes at approximately 3000×g. Remove serum and
assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cycles
Plasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.
Cell culture supernates and other biological fluids - Remove particulates
by centrifugation and assay immediately or aliquot and store samples at -20℃or
-80℃. Avoid repeated freeze-thaw cycles.
Note: The samples shoule be centrifugated dequately and no hemolysis
or granule was allowed.
Materials required but not supplied
1. Standard microplate reader(450nm)
2. Precision pipettes and Disposable pipette tips.
3. 37 ℃ incubator
Precautions
1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.
2. Do not remove microplate from the storage bag until needed. Unused strips
should be stored at 2-8°C in their pouch with the desiccant provided.
3. Mix all reagents before using.
Remove all kit reagents from refrigerator ａnd allow them to reach room temperature
Assay procedure
1. Prepare all reagent s before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.
( 20-25°C)
Materials supplied
2. Add standard: Set Standard wells, testing sample wells.
standard well.
Add standard 50μl to
| Name | 96 determinations | 48 determinations |
| Microelisa stripplate | 12*8strips | 12*4strips |
| Standard | 0.3ml | 0.3ml |
| Sample diluent | 6.0ml | 3.0ml |
| HRP-Conjugate reagent | 10.0ml | 5.0ml |
| 20X Wash solution | 25ml | 15ml |
| Chromogen Solution A | 6.0ml | 3.0ml |
| Chromogen Solution B | 6.0ml | 3.0ml |
| Stop Solution | 6.0ml | 3.0ml |
| Closure plate membrane | 2 | 2 |
| User manual | 1 | 1 |
| Sealed bags | 1 | 1 |
3. Add Sample: Add testing sample 10μl Then add sample diluent 40μl to testing sample well; Blank well doesn’t add anyting.
4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip ａnd incubate for 60 minutes at 37°C.
5. Aspirate each well ａnd wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper
Note: Standard concentration was followed by:towels.
40、20、10、5、2.5、0 ng/mL.
6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well.
Reagent preparation
Gently mix ａnd incubate for 15 minutes at 37°C. Protect from light.
20×wash solution:Dilute with Distilled or deionized water 1:20.
7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.
8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.
Calculation of results
1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis.
2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software.
3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration.
4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.
5. The sensitivity by this assay is 0.1 ng/mL.
6. Standard curve
Storage： 2-8℃. validity： six months.
FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH
ENTIRE PROCEDURE BEFORE BEGINNING!
本試劑盒只能用于科學研究，不得用于醫學診斷
更新時間：2024/5/24 11:45:35
| 您感興趣的產品* | 您還沒有輸入您感興趣的產品 | |
| 您的單位* | 您還沒有輸入您的單位 | |
| 聯系人* | 您還沒有輸入聯系人 | |
| 聯系電話* | 您還沒有輸入聯系電話 | |
| 詳細地址 | ||
| 常用郵箱 | 您輸入的郵箱格式不正確 | |
| 請輸入您對我們的意見或建議* | 您還沒有輸入您對我們的意見或建議 | |
| 驗證碼* | 您還沒有輸入驗證碼 |
溫馨提示
1.遵守中華人民共和國有關法律、法規，尊重網上道德，承擔一切因您的行為而直接或間接引起的法律責任。
2.請您真實的反映產品的情況,不要捏造、誣蔑、造謠。如對產品有任何疑問,也可以留言咨詢。
3.未經本站同意，任何人不得利用本留言簿發布個人或團體的具有廣告性質的信息或類似言論。
首 頁| 公司介紹| 產品展示| 公司新聞| 榮譽證書| 資料下載| 技術文章| 聯系我們| 客戶留言
阿儀網 設計制作，未經允許翻錄必究.
聯系人：段煜 聯系電話：15214379366 ICP備案號：滬ICP備15046135號-2
總訪問量：4289522 管理登錄
主營產品：ELISA試劑盒，標準品，細胞株，抗體，生物試劑，化學試劑，培養基，血清，實驗耗材，ABcam抗體，CST抗體，Santa抗體，ATCC細胞株，人elisa檢測試劑盒，小鼠elisa試劑盒，大鼠elisa試劑盒，牛elisa試劑盒，羊elisa試劑盒，豬elisa試劑盒，犬elisa試劑盒，植植物elisa試劑盒，elisa 檢測試劑盒報價，試劑盒批發，免費代測elisa 試劑盒，細胞株供應商，實驗外包
掃一掃，關注我們
王小姐
